Finite element analysis of composite drive shaft engineering essay
For the two section type cf drive shaft were overlay structure and connection structure design, and through the finite element analysis and test on the performance of the prototype was verified the results show that the test results are consistent with the cae analysis results. The finite element method was used to analysis the natural frequencies of the carbon fibre-reinforced plastic tube and carbon fibre reinforced plastic shaft with steel joints, respectively, which showed that there was a remarkable difference between the two results the difference indicated that the. Composite drive shaft segment with and without damage at different locations are carried out for various boundary conditions to determine strength, stiffness using conventional stress analysis and fea package, ansys.
Automotive composite hybrid drive shaft - a review sunilkumar m bandgar 1, nitin n more 2 life and failure types of composite tubes finite element analysis has been used to predict the fatigue life of for the power transmission shafts, which utilized in many engineering practical uses an including. Ijedr1501041 international journal of engineering development and research (wwwijedrorg) 217 finite element analysis of composite flat c-spring of car rear suspension under dynamic load 1deepak s patil, 2vilas r gambhire, 3prashant j patil have done work in optimal design and analysis of automotive composite drive shaft d abdul budan, t. Design of a composite drive shaft and its coupling for automotive application mr khoshravan, a paykani department of mechanical engineering, parand branch, islamic azad university abu talib et al  implemented a finite element analysis to design composite drive shafts.
Of mechanical engineering, sanjay ghodawat group of institutions atigre, maharashtra, india of composite drive shafts, and a finite element analysis is analysis of composite drive shaft for automotive application. Natural frequency & mode shape of composite drive shaft prof bhirud pankaj p p 1 modal analysis of composite drive shaft which is used for performed by finite element analysis software ansys workbench the shaft modeled in catia v5 & imported in ansys for analysis the result obtained from theoretical. Faculty of mechanical engineering, university of tabriz, tabriz 51666-16471, iran corresponding author: investigate the optimal design and analysis of composite drive shafts with different materials and fibers orientation conducted a finite element analysis to study effects of. A hybrid composite drive shaft, using different windings are wound on the outside of the aluminium drive shaft and made number of layers and stacking sequence, the shaft is under static torsion the numerical analysis is done on the shaft using the ansys software. This paper presents review on finite element analysis investigation of composite drive shaft in static, modal and buckling analysis in respect to advantage of using composite materials in terms of weight and stress minimization, effects of fibers winding angle and layers stacking sequence on the critical speed, optimization into single piece.
Of the finite element method (fem) is used to model the bert and kim  have analysed the dynamic instability of a composite drive shaft subjected to a boukhalfa et al / free vibration analysis of an embarked rotating composite shaft using the hp- version of the fem 109. The composite drive shaft as compared to steel drive shaft is about 8347 % these results are encouraging and suggest that ga can be used effectively and efficiently in other complex and realistic designs often encountered in engineering applications. Dynamic analysis of a hyperbolic composite coupling h ghoneim a, d j lawrie b the proposed coupling can be readily integrated with a composite drive shaft into a single unit a mathematical uɺɺ+[k]u =0) is derived using the finite element method the effect of two geometric parameters on the dynamic characteristics more. Design and analysis of a composite drive shaft for an automobile muhammad zulfadhli bin md zaki bachelor of mechanical engineering with automotive engineering, universiti malaysia pahang ii composite the finite element method has been used to analyze the hybrid shaft under. S v gopals krishna , b v subrahmanyam , r srinivasulu finite element analysis and optimization of automotive composite drive shaft international journal of engineering trends and technology (ijett.
Finite element analysis of composite drive shaft engineering essay
Comparative analysis of composite materials by using finite element method department of mechanical engineering, late g n sapkal coe, nashik, india poonam s talmale2 assistant professor, department of mechanical engineering, rajendar, kumar  in this paper the design and analysis of composite drive shaft is studied the composite. This paper is concerned with the dynamic behavior of the rotating composite shaft on rigid bearings a p-version, hierarchical finite element is employed to define the model. Mutasher et al 6 compared the results of composite shaft torsion test with the results of the finite element analysis and found that the maximum torque coming from experiment was 4%–20% lower than the results from finite element analysis, which showed the reliability of finite element analysis result as well. Department of mechanical engineering blekinge institute of technology karlskrona, sweden 2007 gummadi sanjay akula jagadeesh kumar optimum design and analysis of a composite drive shaft for an automobile optimum design and analysis of a composite drive shaft for an automobile gummadi sanjay akula jagadeesh kumar finite element analysis 41.
Mechanical engineering, sona college of technology, salem-636005, tamil nadu finite element analysis is a computer based analysis technique for design and analysis of composite drive shaft international journal of scientific & engineering research volume 7, issue 5, may-2016. Finite element analysis of shaft using composite materials without and with damping mohdazharuddin pg student, department of mechanical engineering, malla reddy college of engineering, hyderabad, india cshashikanth design and analysis of composite drive shaft. After reviewing the closed form solution methods to calculate the buckling torque of composite drive shafts, a finite element analysis is performed to study their behavior. Hi-tech provides cae services specifically designed for automotive drive shafts, to engineering clients seeking for rigid and optimized design solutions through effective use of finite element analysis (fea), hi-tech can support clients in developing drive shafts possessing the ability to maintain.
Abstractthe finite element method was used to analysis the natural frequencies of the carbon fibre-reinforced plastic tube and carbon fibre reinforced plastic shaft with steel joints, respectively, which showed that there was a remarkable difference between the two results. A hierarchical beam finite element with six degrees of freedom per node is developed and used to find the natural frequencies of a rotating composite shaft a program is elaborate for the calculation of the eigenfrequencies and critical speeds of a rotating composite shaft. 3 the present work concerned with the dynamic analysis of a rotating composite shaft the numerical finite element technique is utilized to compute the eigen pairs of laminated composite shafts. Finite element analysis (fea) has been performed on variety of a driveshaft and universal joints based on different shaft materials and shaft different operating angles a driveshaft is particularly useful in applications such as taking of transferring torque from one piece of equipment to the other.